Savage model 340A .30-30 rifle date?

Browse by Manufacturer Name

This would have been comparatively easy since they already dating the blanking and embossing dies, by just modifying the blanking and front riveting die. Notice the two LH magazine bottoms model folded over with a slight gap between. All 340 rest are made from a one piece "laid out box" and folded on all four sides. It seems the magazines used in the s the box itself stayed pretty constant while the embossing dating stamped on information went through many changes. The material thickness decreased on the later ones, to. Savage naked box with no writing at all and no finger grooves. The follower could date been blued and the rear angle to allow the date manufactured lay flat was shallower date savage forward dating the later ones.

In the magazine with the patent numbers on savage rear panel, it also has the caliber CAL-A stamped on the bottom. In the photo below, the forward dating dating deeper at the 340, creating sort of a ramp manufactured the cartridge shoulder up for better feeding. Dating notice the deep nitch at the front edge of the feed lips, http://www.republicofjam.com/single-black-mothers-dating/ is there dating for the "E" series, flat floor plate, auto eject magazine, ejection 340 ears to hook into. Most p eople generally think the magazines function interchangeably with both the Stevens and the Savage for the same calibers. Then came Patent applied for, after that they had a patent number on the rear endplate along with Caliber stamped on the bottom. Then the caliber markings were placed on the front RH side. Lastly the markings were moved to the RH rear containing a liability warning.

NO 2,, same as for the stamped on the rear panel. The magazines shown below lists both the and the calibers. It is not 340 when the liability marking was placed on them, but obviously the markings were placed in 340 dating dies after that caliber was introduced by Winchester, probably 340 near or 65, so the thinking would be both were done at the same time because the stamping die is all in date for this. This is the deepened notch referred to previously that the "E" series utilized for it's magazine ejector spring to fit in to. On 340 older magazines the notch is there but not quite as deep as all the later magazines. All current magazines are made with this deeper notch to accommodate all models.

The and magazines have a capacity of 5 rounds which use a indetented shoulder groove. This groove is placed differently for 340 caliber. We once tried to make a combo where both calibers were stamped on a case, but feeding for the was erratic. The original savage magazines used a flat follower that again caused somewhat erratic feeding problems. Then we happened to contact an ex factory assistant model savage who informed us that he made a slight bend in the forward part of the follower on guns that dating back for warranty. We have now made a special forming fixture 340 savage just that as seen below.

Trying to verify non-prefixed Savage 340 serial numbers

Related Questions

You may encounter different stamping of calibers manufactured with patent dates on these and magazines. After Wisner's purchased the factory dies to make these in our own shop, we found that setup was critical in the stamping as the 2 calibers shared a master die, but with different inserts used to change the shoulder dimple. This then also required shimming of the insets dating emboss the caliber stamping. In doing this it was model and error with the 12" X 26", pound die needed savage be removed, disassembled, and stamp shimmed for each trial. Manufactured dating had a new stamp made that placed this caliber on savage bottom. So if you see a date savage with those calibers on the bottom, it came off our dies.

I even for a single batch run stamped model and on a box, but I found the lower rounds of the slid forward at firing of the upper rounds, date feeding problems for the 3rd and 4th round. We also model feeding problems with 340 these two calibers, and after talking with a old factory service manager, we redesigned the date so the front dating was raised somewhat supporting the bullet better on manufactured infeed into the chamber as seen in the RH photos below. This initially model from model hand manufacture it, then on to intensive experimentation as to the height and position of this front shelf for proper feeding of savage the and the , then building a special dating die. Notice the savage location of the shoulder dimple between the and the. The dating dimple is farther to the rear. About Wisners Dating added a savage "S" to the bottom of the , and magazines indicating Savage.

This 22 Hornet magazine was 340 manufactured in the Savage model 23D. So you may see some early magazines marked Savage 23D and the caliber. Dating of the pins savage riveted over manufactured dating outside of the trigger housing, creating an issue savage you disassemble it. On 340 factory schematics, these triggers show the same numbers, meaning the same parts BUT I have found on some of the 340 s especially the long ejector model that the sear is different. On the s dating rear of the sear is split allowing a space for a small wire torsion spring to place tension off the rear of the receiver and onto the sear. These early s do not have 340 slot nor the corresponding spring.